elDalvini @ elDalvini @discuss.tchncs.de

Posts

1

Comments

29

Joined

2 yr. ago

I mean, I don't like AI. But leaving in debugging messages can easily happen without AI, too.

I think most of us are pretty damn average.

That's true. Like, by definition.

This seems to be an engineering sample CPU. Since these are pre-production, that could mean it's basically a fully functional CPU. It could also have serious issues.

You can use most of the connectors you would use for bigger wires. Wago lever nuts are rated for conductors as small as 0.14 mm².

If you want something to fit a din rail, standard terminal blocks (something like this) should also work.

Unpopular opinion: The license makes sense and should have been enforced from the start.

The Benchy is a benchmarking tool, not just visually but there are also various features you can measure and check against the dimensions on the website. But that doesn't work if the model you're printing has been modified.

If it looks like a beachy, it should have been printed from the original model, so it's always comparable. Preventing derivatives means you can be sure of that, even if it came on the included SD card with your printer. Otherwise, manufacturers could include a modified model that makes their printers look better than they are.

HiPER Calc Pro. A great scientific calculator I use constantly. (There is also a unpaid, ad-supported version, and the ads weren't too intrusive the last time I tried it)

This seems to be a bug in the slicer. I'm seeing the same issue in OrcaSlicer if the skirt height is set to more than one layer (even if the skirt is disabled). This makes sense if a skirt is used (can't print a continuous spiral if you have to switch between printing the object and the skirt), but not if it's disabled.

What slicer are you using? If it's a PrusaSlicer fork, this is likely the same bug.

Do you expect every meme to be meticulously handcrafted? It's a stupid joke, not a work of art.

Close, but the word ends in -le, not -ie. The -le suffix is used as a diminutive form in some German dialects.

My router is called Jupiter, everything connected to it is named after a moon. Callisto, Ganymede, Thelxinoe, Kallichore are what I'm currently using.

You can host a Firefox sync server yourself. You could run that on something like a Raspberry Pi in your local network. If you need remote access, use something like cloudflare tunnels (although I guess that's something else to be paranoid about).

It is more efficient to have a ship moving with cargo than without, but that doesn't mean there aren't additional emissions. The ratio of profit to effort is just higher because there is some profit as opposed to none. You wouldn't load a ship up with useless mass you can't sell just so you're shipping something.

Your argument is like always running the heater in your car because that way the engine heat is at least used for something. Yes, technically the efficiency goes up because more of the energy in the fuel is harnessed. But that doesn't mean the fuel usage or emissions are any lower, and in the summer the heater doesn't do you any good either.

That's why I don't let every device decide individually. I know my router (FritzBox) prioritizes the pi-hole (it's even called "preferred" and "alternative" DNS-Server in the UI)

I have my pi-hole setup as the upstream DNS in my router, with cloudflare as a secondary DNS. That way, all my devices always use the router for DNS (since that's what is advertised in my DHCP) and the router then uses pi-hole if it's available, or cloudflare if it isn't. But the individual device doesn't get to choose between different servers.

That study states that brain damage can cause more conservative views, but the reverse isn't true. Not everyone with conservative views has brain damage.

Tightening the belts seems to have helped, but I will have to do some more printing to be sure. Thanks for your help!

The belts are parallel to the axis, but I will try tightening them some more.

This is a 40x40 cube printed in vase mode:

The corners look pretty okay on that:

But I don't see these kind of results on real-world parts. I guess I have to print some more test parts to narrow down the problem.

That might be part of it, my filament is probably pretty wet. I'll try some other rolls of filament.

The part is just pretty small, I have the EW set to 0.45 mm withe 0.4 nozzle. But I will try turning it down further.

The rounding looks much more extreme than what I would expect or have seen on other printers I worked with (mostly Ultimakers).