If you're getting nozzle clogs, then it's probably not necessarily moisture but dust being an issue. Dusty and dirty filament pulls dust into the hotend, and the dust doesn't melt so the buildup clogs the nozzle. I've made rudimentary wipes by stabbing the filament through some foam (the grey stuff you find in pelican cases) so that it'll clean the filament of any surface dust as it travels through.
For drying the filament, I set the heated bed to just below the glass transition temp of the filament, put the spool on and leave it there. There are some guides for other methods, but I haven't tried anything else so I can't comment on them.
Are the filaments still in their original packaging and if not, how were they stored? The main thing with old filaments is how much water they've absorbed from the environment, with older filaments stored in high humidity environments causing issues for print quality.
If your filaments have been stored sealed in original packaging, they'll probably print like new. If they've been stored in an airtight container they'll probably also be pretty good. You can also just give them a shot and see if you're happy with the quality they provide.
If they've been stored open on a shelf, it isn't necessarily over for them though. Look up guides on how to dry out filament. There's a few products you can buy that do it too, but if you have a printer with an enclosure and heated bed you can use that as an oven to bake out your filament.
I've got a few filaments that have been sitting for over 6 years and after baking out they print absolutely fine.
To be clear, that's Cataclysm:Dark Days Ahead or CDDA. It's quite removed from the original cataclysm by whalesdev, and is more focused on strict realism. There is also Cataclysm Bright Nights which is closer to the arcadey feel of the original. Both are great and are open source.
Going to submit my probably-not-a-puzzle-game-game: rhythm games. The game tells you exactly what to press and when you're supposed to press it, it's just up to you to actually press the buttons. See: DDR, Rhythm Doctor.
Note that there are rhythm games that have more decision making like crypt of the necrodancer (rhythm roguelike)
Yes, it really is that bad. We have a resin printer at work and it has been banished to a different room due to the resin fumes. The table it sits on is perpetually sticky, and we go through twice as much IPA postprocessing the prints than we use in resin
Cataclysm: Dark Days Ahead. Zombie survival roguelike, forked from the original cataclysm by whales. Also check out Cataclysm: Bright Nights which is a fork of CDDA that makes it more gamey like the original, and less like you're playing 2d arma.
Sunshine and moonlight are open source implementations of nvidia's game streaming protocol they created for the nvidia shield. You can use it to remotely use your computer from your phone, not just for games. But of course the primary application is game streaming. As long as the game can run on the host (sunshine) computer, you can remotely play it on the client (moonlight) device. I've used it to just launch steam in big picture mode and then select what I want from steam.
Powering the laser takes 300 MJ but the actual laser power (the energy in the light) is only 2.05 MJ. The rest of the energy is lost to heat and other inefficiencies. If the laser could be created with 100% efficiency then the input energy would also be 2.05 MJ.
You have to add them manually, either by url or with the built in search. For example, you can add newpipe by searching sources and checking github as a source to search. It will then show you repos that match newpipe, which usually is the regular newpipe repo and then a bunch of forks of it.
Obtainium isn't for finding FOSS apps, it's for installing them. To find them, you can check out existing repos such as f-droid or izzy, or you can ask around. This post has a bunch of recommendations in the replies
Obtainium lets you install FOSS programs directly from the developers source. You can get updates from the github/gitlab of app developers before they get uploaded to F-droid.
Hyperrogue is not quite a top down hexagon world, it's a top down heptagon world. The premise is that it is a roguelike set in a hyperbolic world, and different regions teach you different weird properties of a hyperbolic space. For example, the crossroads feature an infinite amount of parallel lines and yet there are still forks in the pathway.
Even though it's foss, it is also for sale on steam if you want to support the dev
Lossless Cut
FOSS, Crossplatform frontend for ffmpeg. Note that to do it losslessly, it will still be in mp3. If you need to transcode you can do that too, but like others have said you'll probably lose quality.
Near the bolt holes joining the two halves, you can see thin strips going across that overhang gap. Those eliminate local sagging without needing support material.
The part could have been flipped 180 instead, but then the outer edge rim would be unsupported.
If you're getting nozzle clogs, then it's probably not necessarily moisture but dust being an issue. Dusty and dirty filament pulls dust into the hotend, and the dust doesn't melt so the buildup clogs the nozzle. I've made rudimentary wipes by stabbing the filament through some foam (the grey stuff you find in pelican cases) so that it'll clean the filament of any surface dust as it travels through.
For drying the filament, I set the heated bed to just below the glass transition temp of the filament, put the spool on and leave it there. There are some guides for other methods, but I haven't tried anything else so I can't comment on them.