Prismo @ Prismo @lemmy.world

Posts

3

Comments

39

Joined

2 yr. ago

I added some swear words as contact names, this is one way to get around the fucking censorship

Does mean that the unvaccinated anti-vaxers will keep away from the vaccinated??

At least one cat 6 ethernet in each room. Multiple outlets in any media room. One of my old houses had speaker jacks in each corner of the room which was a godsend when setting up surround sound for a home cinema setup.

Copse was my initial thought, but there is also the word Spinney.

https://www.dictionary.com/browse/spinney

Here’s a Piped link to the video in the article:

https://piped.video/watch?v=83ShvgtyFAg

I guess I’ve been looking at it wrong the whole time! Although, living in the countryside would be preferable for moustache-rainwater

I appreciate the usefulness of my eyebrows to divert rain away from my eyes. I do not appreciate my moustache’s water gathering properties when walking in humid environments.

Surprisingly this chair has come out highly in reviews when compared to 4 figure chairs. I have it and can say it is very comfortable. It’s not going to be the best of the best, however if your budget doesn’t stretch to more than mid-3 figures this could be a good alternative.

https://www.ikea.com/gb/en/p/markus-office-chair-vissle-dark-grey-30261152/

https://www.shortlist.com/lists/best-office-chairs-401080

I’m pretty sure I’d be ok in multiple realities

So if you’ve had chickenpox your predisposed, not immune?

Yeh, again I’m not sure how efficient using water is but my instinct says it will be a lot better than any mechanical system as they are generally very inefficient!

I’m going to preface this by saying, all I know is that know about the subject was one physics class in college… The teacher mentioned Hydro Pump Storage that pumps water into a reservoir when there is an excess of energy generation then releases it through turbines when there is a surge is energy needs on the grid. Wouldn’t this idea work in a very similar way? If so it would seem feasible as about 15% of the UKs STOR requirements are met in this way.

https://www.nationalgrid.com/sites/default/files/documents/STOR%20%20Fuel%20Type%20Analysis%20Summary%20%28By%20Capacity%29%20-%20Season%208.5%20-%20Final_0.pdf

https://www.sse.com/news-and-views/2023/03/britain-s-largest-pumped-hydro-scheme-in-40-years-gets-100m-investment-boost/

Nice! Maybe I should post my experiences from turning 40 onwards!

This is why I try to make every moment special with them and give them the happiest life possible. It doesn’t make it hurt less, but you can know that you made one souls life as perfect as possible and you loved them with all your heart.

Who wants to do the exact maths to work out the sea level rise of all of this melting? My back of an envelope calculation gives me 4cm, but happy to be proved wrong! I did 1600km3 over 75% of 510,000,000km2

I also found a huge difference between filaments. Creality was terrible for me, Reflow is great

This really summarises the passive aggressive level you get to with a 3D printer: “Lift off the bed now you little fucker!”

So a combination of three changes finally got me back the correct result.

1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
3. Reduced the temp by 10°C apart from the first layer.

Thanks for your help!

So a combination of three changes finally got me back the correct result.

1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
3. Reduced the temp by 10°C apart from the first layer.

Thanks for your help!

So a combination of three changes finally got me back the correct result.

1. Changed the nozzle for a brand new one, that helped a lot but still had a fee issues.
2. Remeasured my extrusion amount and recalibrated the e-steps, they had gone quite a way out.
3. Reduced the temp by 10°C apart from the first layer.

Thanks for your help!