I wouldn't think so, the printer never did this previously. I need to put together some g-code to make the print head move around at a pretty high rate, but without actually extruding anything.
I suspect it's motion/jiggling around related. I guess I could whip up some g-code to see what happens when the printer is still vs when it's moving rapidly.
Agree that the result won't be a perfect print, but I personally prefer this route over printing the other half, sanding the first half flat to account for a partial layer like you said, and then gluing.
I guess it comes down to what you goal is. 90% of my prints are functional and I don't really care if they're a bit ugly at times.
Do you have a pair of calipers that you can use to measure print height? If yes, don't take it off the bed. Measure the height of the print, delete those layers out of the gcode (it's just a text document after all), and reset. Note that the gcode and printer setup might require some fiddling to get right, but I've resumed prints like this without problems before. They don't all look perfect at this layer, but they're certain better than nothing. Once the print loses its hold on the bed, all bets are off.
Hair color changes with age. My mother in law and wife were both blond when they were kids, but their hair slowly turned browner with age. They both highlight their hair to split the difference.
We have two fairly young kids. Their hair is pretty light blond on the top layers, but their bottom layers are quite a bit darker. I suspect the biggest contributing factor beyond genetics is sunlight. Both of them spend a pretty good amount of time outdoors when the weather permits.
I try to keep my writing somewhere in the middle. Easy examples include intent, which is sometimes more important than the explanation itself, as well as outlining alternative ideas/approaches and why they weren't used.
I greatly appreciate insight into the thought process of others and try to pay it forward.
If the kids are truly little this would be an OK move from the US. However, schools in Puerto Rico teach in Spanish which would be a struggle for kids who are not fluent.
Find people who care about what they're working on and they'll go well beyond the extra mile. As an extra motivator, make it clear the company won't be around if they don't succeed. I'm sure these employees have shares, but tha only really matters if the company succeeds (extra motivation!). Unfortunately, there have been a ton of green/green-adjacent automotive "startups" that have struggled to gain a foothold. See also:
I hope you get a decent answer. When we last visited 10 years ago a similar idea passed our minds.
I did some poking around at the time out of curiosity. From what I recall, a decent amount of manufacturing moved there in the 70s to claim made in America, take advantage of cheaper labor, and take advantage of some tax incentives. The incentives were phased out and manufacturing started leaving. Wikipedia .
I am not sure what their economy is like these days, but as with all moves a chunk of it is going to come down to the work you can/want to do and the jobs available, but with remote work living somewhere like Puerto Rico does seem appealing.
I suspect you're going to have the usual island pain points (hurricanes, expensive imports, limited economy, a large swath of the economy tied to tourism) and benefits (consistent weather year round, natural beauty which PR has a ton of, beaches, interesting culture).
Again, I really hope someone with first hand experience chimes in - even if the moved in the other direction from the island to the mainland.
Keeping a woodworking hobby from devolving into tool collecting can be a trick.
This can be true of most hobbies, lol. Amusingly, three others of yours fall into that pattern.
Electronics? If only I had a bigger power supply, higher speed/more channel scope, hot air station, logic analyzer, etc. Guitars? I have friends and coworkers who play. No one only owns one guitar, pedal, amp combo. Gardening? I have quite the setup in my basement to get seeds going, but I live in zone 6 and need to compensate some for the short growing season. Cooking can also be it's own equipment rabbit hole.
Beyond that: Cameras? Choosing which brand of body to use, sensor size, lens collection, tripods/flash/accessories. If you play a tabletop game do you really play a tabletop game or are you looking for an excuse to make and paint minis? 3D printers can be just as much about messing with the printer as actually printing things.
I think it's important to recognize the pattern so you can consciously decide if you want to fall into it or avoid it. For some people, the collecting around the hobby is even better than doing the hobby.
Factories will win this hands down, especially when you're building large/complex items. It looks like the distinction might be "single building" vs "complex or buildings", but VW's Wolfsburg plant is 70 million square feet. The largest plant I've been to isn't on that list, but it's still over a half mile wide - all under a single roof.
Good luck. The company I work at has the exact same problem. Since each system tends to be owned by a different org, and the systems all meet the owning org's needs, you're going to be in for struggle.
Are you in Europe? In the US, our 120 volt mains limit the size of what can go in our normal outlets. I've never seen an electronic grill, unless you mean something that we would call a griddle.
Is the print stopping or does the printer keep going like all is well?
If the printer is continuing like everything is normal, you can surmise that the issue is either the heater, the extruder, or the filament path.
What does your temp graph look like during the print? Oscillations = potential wiring issue, especially if they're not present for the whole print.
Have you caught the printer doing this? Is the extruder clicking? If yes, something is preventing the filament from moving through the extruder. You're either developing a clog or something is preventing the filament from feeding (binding, etc).
If the extruder isn't clicking, and the print continues for a bit, does the extruder slowly chew through the filament? If yes, you probably need more tension on the feed screw. I would still suggest looking for souces of binding.
I wouldn't think so, the printer never did this previously. I need to put together some g-code to make the print head move around at a pretty high rate, but without actually extruding anything.